Name: EZDim 24V LED Dimmer Driver 100W In-Wall Switch
Brand: HitLights
SKU: SWX-24V-100-30-U
Price: 151.97 USD
Availability: InStock

HitLights LED Light Strip Controllers and Dimmers 24 Volt EZDim® Driver and Dimmer Switch - 100 Watt

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

WHAT STANDS OUT:

All-in-one control: Integrated 24V driver + in-wall dimmer in a single device.
Installer-friendly power: Up to 100W Class 2, 24V DC output for low voltage LEDs.
Professional dimming: Smooth low-voltage dimming, power-failure memory, and UL listed safety.

PRODUCT DETAILS:

The HitLights 24 Volt EZDim Driver and Dimmer Switch 100 Watt is an all-in-one 24V LED driver and wall dimmer that powers and controls low voltage LED lighting from a single device in a standard electrical box. It accepts 120VAC input and delivers 24V DC output for 24V LED strip lighting and other low voltage fixtures.

The 24V EZDim provides up to 100 watts of Class 2, 24V DC power for LED loads, supporting roughly 4.1 amps when fully loaded. For longevity, many installers size the connected load to about 80 percent of capacity. EZDim combines an LED driver and wall dimmer into a single UL listed device, reducing the need for separate transformers and compatibility checks between remote drivers and wall controls.

Combines 120VAC input driver and 24V DC dimmer in one integrated unit
Fits a standard single-gang recessed electrical box with no derating when ganging units
Dimming is PWM based and adjustable from full output down to about 10 percent
Built-in protection for short circuit, thermal conditions, and over-voltage with ≤0.5W standby power

The unit is IP30 rated for dry, indoor locations and requires a neutral connection along with line and load conductors. It is suitable for 24V LED strip lights, under-cabinet runs, shelving accents, coves, niches, and other architectural lighting where a clean in-wall solution is preferred.

Three interchangeable faceplates are included in glossy white, glossy light almond, and glossy dark brown, allowing the dimmer to blend with common interior finishes. A wall plate is not included, so standard decorator plates can be selected to match existing devices. The EZDim carries FCC and UL Class 2 listings and a six-year warranty for added project confidence.

Unlike traditional setups that use a separate wall dimmer and remote low voltage driver, this integrated design simplifies wiring, minimizes installation time, and reduces potential failure points in LED strip lighting systems.

WHAT'S INCLUDED:

1 × HitLights EZDim 24V 100W in-wall dimmer driver switch

FREQUENTLY ASKED QUESTIONS:

Q: What is the HitLights 24V EZDim Driver and Dimmer Switch used for?
A: The HitLights 24V EZDim Driver and Dimmer Switch is an integrated 24V LED driver and in-wall dimmer for low voltage LED lighting. It converts 120VAC to 24V DC and provides local dimming control for 24V LED strip lights and similar fixtures from a single standard wall box.

Q: Who is this 24V EZDim driver and dimmer designed for?
A: This model is designed for electricians, contractors, and advanced DIY users installing 24V LED strip lighting in residential or light commercial spaces. It suits projects where a hardwired, code-friendly wall control is preferred over plug-in power supplies or remote dimmers, especially in kitchens, living areas, and architectural accent lighting.

Q: How does the EZDim driver and dimmer switch work?
A: The EZDim accepts 120VAC line voltage and internally converts it to regulated 24V DC while controlling output with PWM dimming. The front dimmer interface provides on/off switching and smooth adjustment from full brightness down to approximately 10 percent, with power-failure memory that restores the previous level after power is interrupted.

Q: What are the electrical specifications of the 24V 100W EZDim model?
A: The 24V 100W EZDim delivers up to 100 watts (about 4.1 amps) of 24V DC Class 2 output from a 120VAC, 50/60Hz input. It offers ≥0.9 power factor at full load, ≤20 percent THD, and ≤0.5 watt standby power, with integrated short circuit, thermal, and over-voltage protection for LED strip applications.

Q: Is the EZDim compatible with 24V LED strip lights and other fixtures?
A: Yes, the 24V EZDim is intended for 24V DC LED loads, including 24V LED strip lights and other compatible low voltage fixtures. As long as the total load does not exceed 100 watts and wiring follows Class 2 guidelines, it can support under-cabinet runs, shelving, coves, niches, and similar installations.

Q: What faceplates and accessories are included with this EZDim unit?
A: Each EZDim unit ships with three interchangeable faceplates in glossy white, glossy light almond, and glossy dark brown to match different interior color schemes. A wall plate is not included, so standard decorator plates can be chosen to coordinate with existing switches and receptacles in the space.

Q: Can the EZDim be used outdoors or in damp locations?
A: No, this EZDim driver and dimmer is IP30 rated and intended for dry, indoor locations only. It should be installed in a standard recessed single-gang electrical box in accordance with local codes, and not placed in wet, damp, or exposed environments.

SHIPPING DETAILS:

Standard Shipping (3-5 Days) - Shipping cutoff 3pm (PST).
FREE ground shipping (UPS or FedEx) on orders of $199 or more
Standard Shipping: Flat Rate $9.99 - Cutoff 3PM (PST)
2-Day Shipping: Rate Based on Weight - Cutoff 2PM (PST)
Overnight Shipping: Rate Based on Weight - Cutoff 2PM (PST)

Input Voltage: 120VAC (108 ~ 132VAC), 50/60Hz (47 ~ 63Hz)
Output Voltage: 24V DC, 60 Watts (2.5 Amps)
Dimension: 1.4 x 2.1 x 4.1 Inches
Power Factor: >0.9 @ 120VAC 60Hz max load.
THD: ≤20% @ 120VAC 60Hz max load. Tested to comply in accordance with IEC 61000-3-2
Stand-by Power: ≤0.5W
Dimming Performance: (100% – 5%)
Protections: Short circuit, thermal runway, and over voltage
Ambient Operating Temp: 0°C to 40°C
IP Rating: IP30 Dry Location
Certifications : FCC, UL Listed, Class 2
Included Face Plates: Glossy White, Glossy Light Almond and Glossy Dark Brown
Connection Type: Hard-Wired
Efficiency: ≥91% @ 120VAC max load
In-Rush Current: Meets NEMA-410 requirement at any nominal input full sine wave voltage and maximum load at 25°C
Leakage Current: <500μA @ 120VAC
Surge/Transient: Tested to meet transients defined in IEC 6100-4-4, level 3 & IEC 6100-4-5, level 3
Dimming: Output voltage is adjustable via sliding lever
Humidity: 8 ~ 90% relative humidity, non-condensing
Warranty: 6 years

SKU	Input	Output	Wattage	Class 2
SWX-12V-040-30-U	120V AC	12V DC	40W	Yes
SWX-12V-060-30-U	120V AC	12V DC	60W	Yes
SWX-24V-060-30-U	120V AC	24V DC	60W	Yes
SWX-24V-100-30-U	120V AC	24V DC	100W	Yes

Certifications:

What is the EZDim® Driver and Dimmer Switch?

The EZDim® is an all-in-one dimmable LED driver and dimmer switch that provides both power and dimming control for low voltage LED lighting. It combines a dimmer switch and LED driver into a single unit that fits into a standard electrical box.

What voltage does the 24V EZDim® output?

The 24V version of the EZDim® outputs 24V DC power to run 24V LED lighting. There is also a 12V version available.

How much power does the 100W, 24V EZDim model provide?

The 100W EZDim® model provides up to 100 watts (4.1 amps) of 24V DC power to LED lighting. However, it is best to use up to 80% of the driver capacity only for longevity.

What types of faceplates are included in this EZDim?

The EZDim® comes with three interchangeable faceplates in glossy white, light almond, and glossy dark brown to match different decors. A wall plate is not included.

Can I put this be used outdoors?

No, since this is IP30 rated it is for indoor use only.

How long is the warranty?

The warranty of this unit is for 6 years.

Does the EZDim® require a neutral wire?

Yes, the EZDim® requires a neutral connection in addition to line and load wires. It will not work without a neutral.

What size electrical box does the EZDim® fit in?

The warranty of this unit The EZDim® is designed to fit into a single gang electrical box.for 6 years.

It the EZDim® dimmable?

Yes, the EZDim® allows you to dim your LED lighting from 100% down to 10% brightness. It uses PWM (pulse width modulation) dimming optimized for LED loads.

Is the EZDim® UL listed?

Yes, the EZDim® is UL listed and meets safety standards for use in the US and Canada.

DATA SHEET

24 Volt EZDim® Driver and Dimmer Switch - 60 Watt Spec Sheet

CERTIFICATION

UL Listing FKSZ.E476239

Great product and great customer service

I installed the dimmer to light up my floating shelves and they look great; I had a problem during installation and Erick from customer service helped me to figure everything out.
Thanks again

Works with Schluter and others

This was a breeze to install, and power's three LED strips including a Schluter Niche. Best deal in town. I'm sure eventually these will come down in price significantly but as a "niche" item, they're pretty awesome. Especially if you don't want remote options. I much prefer a hardwired option.

Item Did Not Work

I'm still waiting on a response to be able to return this item and be reimbursed.

Quality Product

I'v installed approximately 75 of these units and had no issues. Highly recommend. Excellent customer service.

Unique product that solves a key problem with LED install

Having the dimmer and driver in the same unit allows LED installs where they would otherwise not be possible or very difficult.

The downside of this one is it is trapped in a small box so the heat is far more problematic than if your driver was in an open attic.

In spite of this, it was still a better solutions than any other I had so I bought a second one of these and added more strip light to make up for the lower light level than I anticipated.

1 2