Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
The 6 Inch Any Angle 8mm Solderless LED Light Strip Connector (Single Color, 4 Pack) provides a frustration-free way to join or extend 8mm single-color LED strip runs. Each connector uses a simple clasp attachment that locks onto the strip pads, giving a secure electrical connection with no soldering, crimping, or special tools.
A flexible 6 inch jumper cable between the two strip ends makes it easy to cross gaps, bend around corners, or route around obstacles while keeping the lighting run continuous. These connectors are compatible with 2-pin, 8mm wide single-color LED strips (such as SMD3528) on 12V or 24V constant-voltage systems and work with dimmable setups when used with appropriate drivers.
Designed for indoor applications like cabinets, shelving, ceilings, and displays, the connectors feature a compact white plastic housing with internal 22 AWG leads and are rated for typical low-voltage LED strip loads.
WHAT'S INCLUDED:
4 × 6 Inch Any Angle 8mm solderless LED light strip connectors
Q: What size and type of LED strip works with these connectors?
A: These connectors are designed for 2-pin, 8mm wide single-color LED strips, such as SMD3528 tape lights on 12V or 24V constant-voltage systems. They are not compatible with wider 10mm strips or RGB/RGBW multicolor tape.
Q: How do I install the connector on an LED strip?
A: Cut the strip at a marked cut line, open the plastic clasp, align the + and – pads on the strip with the connector pins, slide the strip under the contact prongs, and close the clasp until it snaps. This creates a solderless, tool-free electrical connection.
Q: What is the maximum voltage and current these connectors can handle?
A: Each connector is rated for 12–24V DC and up to 3A of current, which is sufficient for most short single-color LED strip runs. Always confirm that the total strip load on each connector stays within these limits.
Q: Can these connectors be used outdoors or in damp areas?
A: No. With an IP20 rating, the connectors are intended for indoor, dry-location use only. They can be attached to waterproof or outdoor-rated strips, but the connector itself must be placed in a dry, protected enclosure if moisture is present.
Q: Are the connectors reusable if I cut or move my LED strip?
A: Yes, the connectors can be opened and reused. After trimming the strip on a cut mark, you can re-clamp the connector onto the new section as long as the copper pads are clean, properly aligned, and fully seated under the contact pins.
Q: Is it normal for the connector to get slightly warm in use?
A: A mild warmth during operation is normal when the connector is used within its 3A, 12–24V DC rating. This slight temperature rise is expected and not a concern unless there are visible signs of damage or discoloration.
Q: What warranty coverage do these connectors include?
A: The 6 Inch Any Angle 8mm Solderless LED Light Strip Connectors are backed by a 1-year warranty, covering typical indoor residential and light commercial use within the published electrical and environmental specifications.
SHIPPING DETAILS:
| SKU | Connection Type |
Width | Pin Quantity | Compatible With |
|
CON-08S-B00A-4PK |
Board to Board | 8mm |
2-pin |
Single Color |
| CON-08S-B00A-12PK | Board to Board | 8mm |
2-pin |
Single Color |
| CON-10S-B00A-4PK | Board to Board | 10mm |
2-pin
|
Single Color |
| CON-10M-B00A-4PK | Board to Board | 10mm |
4-pin
|
RGB Multicolor |
| CON-10M-B004-4PK | Board to Pin | 10mm |
4-pin
|
RGB Multicolor |
| CON-10M-B00A-12PK-NEW | Board to Board | 10mm |
4-pin
|
RGB Multicolor |
| CON-10S-CS10-10PK | Board to Board | 10mm |
2-pin
|
Single Color |
| CON-10S-COB-PKGH | Board to Board | 10mm |
2-pin
|
Single Color |
